But now I have 3Com switch. Stack Exchange Network Stack Exchange network consists of 174 Q&A communities including Stack Overflow, the largest, most trusted online community for developers to learn, share their knowledge, and build their careers. Control is a small freeware utility that facilitates tweaking of core parking and CPU frequency scaling settings of Windows power plans. Patch My PC can check your system against the current version of Adobe Reader/Acrobat/Flash, Mozilla Firefox, and more. The Driver Update Tool – is a utility that contains more than 27 million official drivers for all hardware, including pci 10/100 lan card by 3com (ethernet) driver. This utility was recognized by many users all over the world as a modern, convenient alternative to manual updating of the drivers and also received a high rating from known computer publications. The utility has been repeatedly tested and has shown excellent results. This tool will install you the latest drivers for all devices on your computer. Supported OS: Windows 10, Windows 8/8.1, Windows 7, Windows Vista. This utility contains the only official version for PCI 10/100 LAN card by 3Com (Ethernet) Driver for Windows XP/7/Vista/8/8.1/10 32-bit and 64-bit versions. With just one click you can update the driver as well as the rest of the drivers in your system, such as: • Monitors • Audio & Sound • Graphics & Video Adapters • Modems & Network Adapters • Printers • Scanners • Optical Disk Drives • Other Devices This utility works in two simple steps: 1. Automatically identifies your Hardware. Downloads the latest official version of the drivers for the Hardware and installs them correctly. This method allows you to save your time and correctly install all necessary drivers, not being afraid to make a mistake during a manual installation. AGENT UPGRADE UTILITY D The CD-ROMsupplied with the hub has an agent upgrade utility on it that can be used for upgrading the new version of agent software to the PS Hub. NOTE: You would only use this utility if a previous software upgrade has failed and you are unable to communicate with your hubs using the web interface or Quick Config Manager. At all other times you should use the web interface or Quick Config Manager to upgrade your hubs. If you have any problems using the agent upgrade utility, refer to “Solving Problems With the Agent Upgrade Utility” on page D-3. Using the The upgrade utility works from an MS-DOSprompt. Glock pistol date of manufacture by serial number. It upgrades one Upgrade Utility hub at a time. Upgrading a hub may take up to 5 minutes. To upgrade agent software to a hub: 1 Connect your PC’s serial (COM) port to the hub’s console port, using a null modem cable. 2 If you are using Microsoft Windows, exit out of it so that you are at the MS-DOSprompt. This utility must be run from MS-DOS.It cannot be used from an MS-DOSWindow within Microsoft Windows. 3 At the MS-DOSprompt, change your directory to the drive that is your CD-ROMdrive. D-2 APPENDIX D: AGENT UPGRADE UTILITY 4 Enter the upgrade command: ■ PS Hub 40 software upgrade — update psh xx _ yy.bin ■ PS Hub 50 software upgrade — update psf xx _ yy.bin Where xx_ yy is the version of agent software. The version of agent software on the CD-ROMis the current version that was in the hub originally. View the contents of the CD-ROMto see the filename for this version of agent software. You can also use the following parameter with the upgrade command to specify the serial (COM) port to use for the PC. The default for this is COM 1: -c1 or -c2 An example of the upgrade command with this parameter is: update -c1 psh xx_ yy.bin 5 Power off the hub. 6 Press [Return]. 7 Power on the hub immediately (within 5 seconds). Holux gps receiver. The utility transfers the agent software to the hub. 8 Repeat all of the steps for any other hubs that need upgrading. Solving Problems With the Agent Upgrade Utility D-3 Solving Problems If you have any problems using the upgrade utility, use the following With the Agent actions to solve your problems. Upgrade Utility An error occurred when the utility tried to connect through the PC’s serial port. The serial port being used is not the same as the serial port specified in the upgrade command. Retry the command ensuring that you specify a value of ‘1’ or ‘2’ for the serial port. An error occurred when the utility tried to communicate with the hub. There could be a number of reasons for this: ■ The hub was not powered on within 5 seconds of pressing [Return] (step 7).
0 Comments
Leave a Reply. |